XDA Flame User Forum at xdaflameusers.com

Tried recovering my flame using the above procedure, I got the following message after running start.bat

JFLASH Version 5.01.007
COPYRIGHT <C> 2000 - 2003 Intel Corporation

PLATFORM SELECTION:
Prcoessor=                   PXA27x
Development System=  Mainstone
Data Version=              1.00.001

error, failed to read device ID
check cables and power
ACT: 1111 1111111111111111 11111111111 1
EXP:  **** 1001001001100101 00000001001 1

failed to read device ID for this Platform


I checked and re-checked the following:
           1. connections and the cable that matches the daigram and the picture
           2. Power and made sure that there is power
           3. also re-initiated the giveio driver just to be sure.

I used 1.5v 100 ohm resistors and used HDD IDE wires for wiring

Not sure what's the cause of the problem. My guess is that the giveio driver is not recognized. I'll try later using safe mode to see if I have a IO conflict in the LPT port.

Anybody got any ideas?

Thanks in advance

Update: giveio does not work in safemode. after playing around the software giveio is loading as com3, which is the likely reason why the hardware is not detected on the LPT port. so far I can't find an instruction how to load it in LPT1. I'll try again later with another PC.

Last edited by Steele (2008-04-24 11:52:37)

Thanks Medush.

So far it is the same when trying on a different PC.

I'm doing a new wiring again just to be sure.

I rechecked my previous setup with the list you have made:
1. The resistor is correct 100 ohm with color bar Brown-Black-Brown-Gold (LPT is connected near the Brown stripe and wire to motherboard is connected near gold stripe)
2. Wiring distribution is okay. Checked also wiring with voltmeter to see if there are damages or disconnections in the setup. So far it is okay from LPT pin to end wire.
3. Cable used is 18cm
4. Solder is okay on the LPT plug. except for the flame motherboard. solder cannot attach on the board contacts. Have to use tape to hold the connections in place.
5. Accu button not pressed.
6. Power cable is connected.

I'll make some tests after re-wiring. and let you know any developments.

Thanks.

Last edited by Steele (2008-04-25 09:51:19)

Congratulations! I update my Paypal account

Last edited by medush (2008-04-30 01:02:17)

wksoo

You use invalid filename. True name is diskimage.nb0
Please correct and re-flashing this file.

tora_tiger wrote:

Hi.my flame is not power on.Can I recovery it?

Why your device does not join?
It after flashing?
Or other reason?
The battery is charged?

If the device has died after a flashing - use my method for recovery.

Last edited by medush (2008-05-13 18:57:50)

I have bricked my O2 Atom Life,it absolutely dead now ,how can i recover it?can you send me e-mail to afeng114@163.com,thank you!

Last edited by afeng11 (2008-06-10 07:57:02)

medush wrote:

afeng11 wrote:

I have bricked my O2 Atom Life,it absolutely dead now ,how can i recover it?can you send me e-mail to afeng114@163.com,thank you!

You can try this metod: http://forum.xda-developers.com/showthread.php?t=336278

I want to advise you create new topic in http://pda2u.ru/forum/index.php?s=& … p;cal_id=0 (like English )
This forum - a place of a meeting of the professionals having wide experience on reanimation of devices

thank you,first,i didn't know jtag point in atom life,and atom life is m-system's DOC,so flashmm software can't fit to Atom life!any advise?i can read any russia,sorry!

Last edited by afeng11 (2008-06-10 16:09:54)

medush wrote:

afeng11 wrote:

thank you,atom life is m-system's DOC,so flashmm software can't fit to Atom life!any advise?i can read any russia,sorry!

Flame is DOC too and jFlashMM connected to this device successfully.
Create a new topic in English, we will respond also to you in English.
If you have errors at connection JTAG - write about them in detail, lay out a screenshots...

sorry,i didn't know the jtag point in atom life,can you tell me?thanks!


i want create a new topic,but i must register first,but i can read any russia,sorry!


this was my message when i use jflashmm:
D:\Flame\ATOM EXEC JTAG\RepairBootLoader(EXEC)\JFlash_MM>jflashmm pxa27x32 ebo_
.nb0 N 0 PAR

JFLASH Version 5.01.007
COPYRIGHT (C) 2000 - 2003 Intel Corporation

PLATFORM SELECTION:
Processor=             PXA27x
Development System=    Mainstone
Data Version=          1.00.001

PXA27x revision ??
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 4 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 3 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 2 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 1 more times...
Upper and Lower flash memory ID does not match.
You may have a damaged flash memory.
Upper half reads: 90
Lower half reads: F000
Failed to read the Flash ID. Retrying 0 more times...
Cannot open input file: Flash_f000_2_32.dat

This program supports flash devices defined by DAT files
contained in the same directory as the executable program.

If the file cannot be opened, there are four possibilities:

1 - The flash device installed is not supported.
2 - The flash device is a licensed product.
3 - The device ID could not be read, resulting in a poorly
     constructed filename. The first numeric value in the
     filename is the device ID. Verify this value with the
     component specification.
4 - The memory bus is not functional. Check all CPLD and FPGA
     devices. Make sure that you are using the correct
     platform data file.

Last edited by afeng11 (2008-06-11 08:58:44)

I create new topic here: http://pda2u.ru/forum/index.php?showtopic=338&st=0

afeng
All discussions only there, on English.

thierryb
Sorry for offtopic.

Last edited by medush (2008-06-10 18:46:59)

My 02 Flame became bricked after 2nd time of loading to WM6.1 (1st time ok but after few day found something decided to reload os) -screen shows "completed" and freeze (unlike 1st time reset system itself), so I power off and on but no response anymore....no light nor screen...have try thousand of methode but still completely no response at all....sick !
anyone know the pin config beside the SIM card holder for 02 Flame ? does it related to JTAG ? -so that we don't need to dismantle to access to JTAG signals !
also the JTAG use 25pin D-Shell, how to convert to 9pin D-Shell ? -only old computer still using 25pin D-Shell !
Thanks for any feedback !

Thanks dwalin, I mistaken that is a serial port, but just wonder anyway to access to JTAG without completely dismantle motherboard !

About a week ago i was flashing my Flame with the WM6.1 ROM and during the OS Upgrade process it freezes at 10% of ''erasing flash''. I opened the eboot.nb0 file with an editor and inside there are some words like ''erasing flash failed'' etc etc, i don't get these it just freezes at 10%. Does this happen to anyone before??? and is there a way to enter some king of menu with the rerr003a.kez file or some other and reach the ''Format flash'' option what i found in eboot.nb0 under ''Arima engineer menu''. The only key combination i discovered with the rerr003a.kez file is the winkey and reset, it's showing some kind OS Reconstruct with the image not found error and continues to the err-003a screen.
With the wdzkfnma.kez and i key combination, in the menu i found the select boot device option, when selecting USBFn as first  boot device, the device get recognized by the computer as a USB piece of hardware but i don't have any driver for this, does anyone know where to find some kind of driver and what it is for?. I hope it's something like mtty.exe for the HTC devices.
Is there a way to format the flash of the flame (better without erasing the eboot.nb0 area)??
Thank you for any answer to this...

Last edited by alen909 (2008-07-30 15:03:48)